Browse all practice questions for the GENESIS C201 Concrete Pools Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

GENESIS C201 Concrete Pools Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • With a plasticity index of 40 to 60, which option should be excluded from consideration?
  • What is the role of suction and return lines in a concrete pool's plumbing system?
  • How should cold joints be treated in a concrete pool?
  • Why is proper formwork and alignment important during concrete swimming pool construction?
  • Admixtures cannot be added to dry shot concrete.
  • Which statement correctly describes the target LSI range for a balanced pool?
  • What is the minimum allowable compressive strength value with a maximum water-cement ratio by weight of 0.45?
  • What aspect should be anticipated as significantly impacted when epoxy-coated rebar is used in a pool deck?
  • Which statement about bond breakers in pool plaster is true?
  • How do reinforcing steel in concrete resist thermal expansion or shrinkage forces?
  • In intersecting arc method for pool layout, only the distances are measured and not angles.
  • What should be done with fiberglass and paint on renovated surfaces?
  • If epoxy-coated rebar is specified for a swimming pool deck, what impact does this have on the builder's responsibilities?
  • Which dampproofing product can be used in fresh concrete mix or applied to the finished surface?
  • The pipe support spacing should not exceed 36 inches for 1" pipe.
  • For surface preparation, the Concrete Surface Profile (CSP) should be ___ or greater.
  • What is bonding and grounding in pool electrical work?
  • What describes the difference between a bond beam and coping?
  • Which method is commonly used to identify a leak in a finished concrete pool?
  • If bottom is not more than 4 inches from a hard surface, what is the minimum barrier height?
  • To calculate the number of gallons inside a vessel, you multiply the cubic foot volume by which conversion factor?
  • Setback distance for spoil from excavation edge is equal to the depth of the excavation.
  • Which type of stress primarily causes flexural deformation in members?
  • Calculate the change in length of this concrete deck: 40' long 20° winter 100° summer.
  • Doubling the flow rate will cause headloss to quadruple.
  • On renovated pool surfaces, what is the recommended action regarding fiberglass and paint?
  • Which measures help prevent wall collapse during excavation in unstable soils?
  • In loose soils, which scenario best describes additional measures during excavation?
  • How is the verticality of walls and floor slope typically verified during pool construction?
  • What is the practical time limit to make saw cuts for contraction joints in concrete deck work?
  • What is the importance of proper slope at the pool floor?
  • How do you typically verify water leaks in a concrete pool after plaster?
  • What is the primary purpose of a bond beam?
  • Why is a coping edge important for water containment and aesthetics?
  • Which statement about alkalinity and plaster surfaces is correct?
  • What factors influence the choice of interior finish in a concrete pool?
  • What is a skimmer's primary function?
  • PVC pipe should not be run parallel to walls or floors within the required structural thickness.
  • How does hydrostatic pressure influence pool design when the shell is unfilled?
  • What is the most frequent cause of plaster finish failures?
  • Why is interior shell waterproofing essential in concrete pool construction?
  • When installing tile near plaster, what is essential to ensure plaster adhesion?
  • Under track for automatic pool covers requires coping overhang of 3 inches from shotcrete and 2.5 inches from tile.
  • Which feature helps accommodate movement due to temperature changes in concrete pools?
  • Why is surface water balance critical for plaster compatibility?
  • If renovating a pool surface includes fiberglass or paint, what is the recommended action?
  • What is the purpose of adding fly ash & silica fume to concrete mix?
  • Which is better for pool tiles? Porcelain or ceramic?
  • Cyanuric acid is ideal for indoor pools.
  • How can tile bezels or glass tile installation affect plaster adhesion?
  • What does plastic limit refer to?
  • An 18in diameter column with a vertical load of 15,000 pounds is to rest on a 6 inch thick concrete floor. The compressive strength of the concrete is 4000 psi. What is the capacity of the concrete floor?
  • What is the maximum water-to-cement ratio by weight mentioned for the compressive strength requirement?
  • What is the maximum flow rate for a high rate sand filter?
  • What is the purpose of anticorrosive coating on metal components inside a pool?
  • Construction specifications typically include the section number for each trade involved in a project.
  • What is the function of return lines in a pool's plumbing system?
  • Voltage drop along long conductor runs can cause equipment to operate at a lower voltage and fail.
  • Aside from sealing, what aesthetic function does plaster provide in a concrete pool?
  • What is backflow prevention in pool plumbing, and why is it required?
  • In pool equipment sizing, which factor should be prioritized to ensure proper operation?
  • What could occur if water leaks in a concrete pool are not identified and repaired before finishing?
  • What is thermal expansion in concrete pools and how is it addressed?
  • What is the target LSI range for a balanced pool?
  • What is the purpose of an air vent or bleed screw during shotcrete application?
  • Using Ohm's law, what is the formula to calculate the voltage?
  • Which steps are typical at the completion of pool shell construction?
  • Push button door lock release distance from floor?
  • In a pool with an interior spa, which design choice helps the cover pass freely over the dam wall?
  • What distinguishes gunite from shotcrete in pool shell application?
  • Name three common interior finishes used in concrete pools.
  • What is the purpose of using an approved bonding agent with cold joints?
  • Torsion is a combination of compression, tension & shear stresses.
  • Which range represents the advisable salt levels in a swimming pool, expressed in parts per million?
  • What are common warning signs of improper plaster application?
  • What is the most important thing to ensure component compatibility between SOFAs, pipes, pumps and filters, or other swimming pool equipment?
  • A mosaic tile mounted on a rubber grid covering 30% of the tile surface is acceptable as long as the mesh is not water soluble.
  • Calculate the flow rate in gallons per minute of water traveling at 5 ft/sec in a 4 in pipe with a cross sectional area 0.087 sq ft.
  • How does proper backfill support the pool structure?
  • How much clearance should be provided in front of electrical distribution panels?
  • Coping is placed on top of which structural element?
  • The presence of efflorescence is a bond breaker.
  • Which force describes squeezing that reduces the cross-sectional area of a material?
  • CSP value should be at least 3.
  • What is the recommended practice for backfilling around a newly poured pool shell?
  • How do you identify a leak in a concrete pool after completion?
  • What is the recommended thickness of plaster finish that is troweled?
  • Which of the following are typical filter media types used in pool filtration systems?
  • Calcium chloride addition is based on which factor?
  • True or False: Yield strength refers to the lowest point on a stress-strain curve of a steel bar before it fractures.
  • What is the purpose of a deck drain or coping channel in concrete pool installations?
  • Which statement best describes the typical components of a pool filtration system?
  • Reinforcing steel resists shrinkage forces due to initial curing.
  • What is the role of a control system in a modern concrete pool?
  • If the pipe length doubles, the friction loss doubles.
  • Which feature can reduce running costs for a concrete pool system?
  • If water infiltration occurs at the plaster surface, which design change would most directly mitigate this issue?
  • What is the advisable range of salt levels in a swimming pool?
  • In a residential grass or landscaped backyard, the NEC requires ____ inches minimum cover over low voltage non-metallic conduit.
  • What are common causes of plaster finish failure in concrete pools?
  • What is the purpose of a bonding grid at the pool equipment pad?
  • In an excavation, how far back from the edge should spoil or vehicles be located?
  • Which term describes the force associated with stretching a material along its length under load?
  • What term describes a defect that is hidden and may not be observable for years?
  • What grade rebar is recommended for pools?
  • Calcium chloride (CaCl2) should be measured and added to the mix on the basis of what?
  • Which combination represents the clearances for soil to rebar and rebar to surface?
  • Are sequestering agents necessary to keep metals from falling out of solution and damaging the pool plaster?
  • During tile installation, temperatures should be between 50°F and what temperature?
  • What is the required hand excavation limit for safe excavation next to a marked utility?
  • What is the required minimum center to center distance between 2 suction outlets?
  • Is organic pigmented plaster more durable than inorganic pigmented plaster?
  • Which statement best describes how floor capacity depends on dimensional and material properties?
  • What is the maintenance difference between a sand filter and a cartridge filter?
  • Under axial loading, which force causes a member to lengthen?
  • The headloss and flow rate in a given pipe are in direct proportion. If you double the flow rate, you double the headloss.
  • What is the purpose of a bonding grid on the pool equipment pad?
  • Which force is described as the force that attempts to slice through a slab across its thickness?
  • What basic measurements are required to order a concrete pool shell on site?
  • What is the least preferred method of cleaning pool surfaces?
  • What effect can improper plaster chemistry have on surface durability?
  • Which chemical helps keep dissolved metals in solution to protect plaster?
  • Which statement about efflorescence in plaster work is true?
  • A shotcrete shell should be water cured and wet down prior to plaster application.
  • What maintenance action is associated with sand filters when pressure rises?
  • The color of the 12 AWG copper wire mentioned in the example is Yellow.
  • What is the efficiency range for gas fired pool heaters?
  • Which item is most directly affected by specifying epoxy-coated rebar in pool decks?
  • Which common dampproofing product can be added to fresh concrete mix or topically applied by spraying the finished surface?
  • What safety or code considerations relate to pool fencing and access?
  • Picket fence minimum height for barriers when bottom is not more than 4 inches from a hard surface?
  • Equipotential bonding is the same as grounding.
  • Which maintenance practices extend the life of a concrete pool?
  • Why is quality testing of concrete important before finishing the shell?
  • What is the function of the return line in a pool filtration system?
  • What is a key implication of hydrostatic pressure on an unfilled pool shell for designers?
  • A shotcrete shell should be _________ finished, water cured, and wet down prior to plaster application.
  • Why is proper curing important after forming a concrete pool shell?
  • Which finishing method is recommended for shotcrete before plaster application?
  • During tile installation, temperatures should be between 50° and what?
  • What happens if water TDS is above 1200?
  • Vacuum breakers are sufficient to prevent back flow.
  • Which maintenance practice contributes most directly to early leak detection in a concrete pool?
  • Which statement best describes the budgeting impact of epoxy-coated rebar on deck construction?
  • Where should the level control be placed when sizing the plunge basin?
  • How should water chemistry be maintained for plaster pools to prevent whitening and scaling?
  • What is the typical construction sequence for a new concrete pool shell?
  • Without shade, ice, air circulators or other precautions, shotcrete should not be placed when temperatures are
  • Which concept refers to moments causing rotation around a point in a structural member?
  • Which of the following standards is not used for the construction of a residential swimming pool?
  • Which feature besides pump efficiency contributes to reducing energy costs in a concrete pool system?
  • If the LSI of pool water is -0.35, what is the water condition?
  • What clearance is required between rebar and the pool surface?
  • Air gaps are usually specified by local code as being two times the diameter of the discharge pipe.
  • In a pool with an interior spa, which design choice helps the cover pass freely over the dam wall?
  • What is the function of pool plaster in a concrete pool?
  • What is the recommended maintenance interval for checking pool equipment operation?
  • What is the primary purpose of reinforcing steel (rebar) in a concrete pool?
  • What is the purpose of a main drain in pool plumbing?
  • Which statement is NOT a typical goal of concrete quality testing before finishing?
  • What is a solution for over excavation?
  • Which factor most directly influences the durability of an interior pool finish in chemical environments?
  • How does a saltwater chlorine generator operate in a concrete pool?
  • What construction approach helps avoid cold joints in concrete pool walls?
  • Which geometric detail is essential to define the curvature of a concrete pool shell when ordering onsite?
  • What is the number one chemistry problem that leads to surface irregularities such as pitting in plaster swimming pools?
  • What maintenance action is associated with cartridge filters?
  • What unit is used for length in the deck length change calculation?
  • Which issue is most likely caused by premature chemical exposure during plaster curing?
  • In the example, which factors contribute to the floor capacity?
  • A PI of 0 would be what material?
  • In the deck length change calculation, what is the temperature difference used?
  • Which of the following is NOT a common interior finish for concrete pools?
  • What is the advisable range of pump suction cover in sizing vanishing edge weir plunge basins?
  • A pump burned out when supplied by a long run with the source at 540 V but the pump received 180 V. Why did this happen?
  • Is it acceptable to fill shotcrete scoops around fittings with plaster?
  • Which action best describes how a deck is supported against vertical loads causing the slab to curve?
  • Ampacity derating occurs when four or more current-carrying conductors are in a conduit.
  • In the intersecting arc method, which measurement is not used?
  • What is the function of a main electrical disconnect in pool systems?
  • Which testing method identifies leaks after plastering?
  • Which interior finish is a common option among plaster, quartz aggregate plaster, and ceramic tile finishes?
  • Which system component is typically installed at the lowest point to drain the pool?
  • Which cost component is most affected when epoxy-coated rebar is specified for pool decks?
  • When building in loose, caving soils, which extra work may be required?
  • What clearance is required for rebar on flat work between the soil and the rebar?
  • The higher the plasticity index, the more likely the soil is to be what?
  • What coefficient is used in the length-change formula for concrete deck thermal expansion?
  • What is common practice for curing concrete in hot climates?
  • Why is tile and coping installed around the pool edge?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy